In sawmills and wood pallet board workshops, sorting, flipping, aligning, and stacking cut pallet boards or dimensional lumber by hand comes with three common problems: too much labor — a single stacking station usually needs 4–6 workers per shift; unstable stacks — manual alignment relies on the eye, so stacks tend to lean and load poorly into the drying kiln; uneven stickers — manually placed drying stickers (sticker) vary in spacing and are sometimes missed, leading to uneven drying and higher deformation rates.

The Automatic Lumber Stacking Line (also known as a Wood Board Palletizing Line or automatic lumber palletizing system) is a complete automated solution built for this stage. It connects automatic feeding, flipping and orientation, centering and edge alignment, automatic sticker placement between layers, layer-by-layer stacking, and full-stack discharge into one continuous line. In normal operation, the entire line needs just one operator.

The machine has an overall length of 11400mm, a maximum height of 5751mm, and a widest section of 1798mm. It is a compact turnkey line that fits flexibly into existing workshop layouts. Once stacking is complete, the finished stack can be transferred directly to the kiln inlet — from lumber cutting to stacking and kiln loading, manual intervention is minimal.

Automatic Pallet Lumber Stacking Machine

Six Units, Each With a Reason to Be There

The line consists of six units. They are not just a list of functions — remove any one of them, and the downstream process runs into trouble.

 1.Automatic Feeding Platform

This is the batch loading station. A full bundle of rough lumber is placed here, and the machine automatically separates boards, feeds them one by one, and handles pallet stock of varying lengths. If feeding were done manually board by board, it would become the bottleneck of the whole line — no amount of downstream automation would help.

2. Automatic Rotation Mechanism (Rotary Drum)

This unit flips boards into the correct orientation, straightens them out, and rejects overlapping or jammed pieces, ensuring every board enters the next stage in a consistent position. If boards go into stacking with mixed orientations, the stack bears uneven loads and shows noticeably higher warping and deformation after kiln drying. It is the sorting core of the line.

3. Wood Finishing and Centering Platform

Boards are automatically centered and edge-aligned during conveying, keeping all four sides of the finished stack straight. This step directly determines stack quality — a leaning stack on the kiln car causes short-circuiting of airflow inside the kiln, and boards in the same charge dry unevenly.

4. Wood Palletizing Main Unit

The core station of the line, with the sticker placement manipulator integrated here. Boards are stacked layer by layer, and drying stickers are automatically placed between every layer to create uniform ventilation gaps. Stacking layers and sticker positions can be preset on the touchscreen. Hydraulic lifting plus servo positioning keeps each layer height precisely controlled, adapting to lumber of different thicknesses.

5. Lifting Table

The table lowers in sync as the stack grows, receiving boards smoothly and preventing drop damage. Once the stack reaches the set number of layers, it rises and transfers the full stack to the discharge conveyor.

6. Discharge Conveyor

Multiple powered rollers move the complete stack out continuously and connect directly to the kiln inlet — no intermediate transfer needed.

Pallet Lumber Stacking Machine x

Working Flow

Bundle loading → rotary drum separates and orients boards → centering platform aligns edges → palletizing unit stacks layer by layer while the manipulator places stickers → lifting table lowers in sync → after reaching the set layer count, the table rises → the full stack is discharged and goes straight to the kiln.

The operator’s job comes down to two things: loading and monitoring.

Manual Stacking vs. Automatic Stacking Line

ItemManual StackingAutomatic Stacking Line
Labor4–6 workers/shift1 operator
Stacking speed10–15 boards/min (skilled)Up to 66 boards/min
Stack alignmentVaries by workerStraight on all four sides
Sticker spacingManual placement, easily missed or unevenManipulator-placed, uniform spacing
Drying qualityAffected by sticker qualityUniform airflow, lower deformation

Technical Specifications

ItemParameter
Overall length11400 mm
Maximum height5751 mm
Stacking unit width1798 mm
Board thickness14–25 mm
Board width70–145 mm
Board length597–1200 mm (custom extension available)
Production speedUp to 66 boards/min
Total power10.5 KW
Control systemPLC + touchscreen, parameter storage, fault alarm
Drive typeHydraulic lifting + servo positioning
Maximum stack heightConfirm by model
Maximum stack loadConfirm by model
Optional functionsAutomatic sticker placement, kiln car docking, scan counting
CertificationCE, suitable for export projects to overseas sawmills

Boundary notes: This line is not designed for oversized or over-thick boards (beyond the above specs, custom evaluation is required). Severely warped or twisted incoming boards need upstream conditioning — the stacking line itself does not straighten boards.

Pallet Lumber Stacking Machine x
Pallet Lumber Stacking Machine x

Applications and Options

Mainly used by three types of customers:

  • Sawmills: dimensional lumber stacked and sent directly to the kiln

  • Wood pallet board workshops: high-volume stacking of pallet boards and packaging stock

  • Wood processing plants with kiln drying: stacking linked with the drying process

Automatic sticker placement, kiln car docking, and scan counting are available as options. CE certification is available for export projects. Board lengths and widths outside the standard range can be customized.

FAQ

Q: The minimum board length is 597mm. Can shorter boards be handled?

The lower limit is set by the rotation mechanism and positioning accuracy. Boards shorter than this cannot maintain consistent orientation — we recommend sorting them upstream.

Q: How long does it take to change specifications?

Board width, thickness, and stack layer count are preset on the touchscreen. Routine changeover requires no mechanical disassembly — exact time depends on the specification difference.

Q: Is compressed air required?

Yes. The line connects to the workshop air supply. Exact pressure and flow requirements are confirmed with the final configuration.

Q: Can it dock with our existing kiln cars?

Yes. The discharge conveyor height can be customized to your kiln car dimensions, and the optional kiln car docking function enables automatic positioning.

Q: How can we verify the machine’s stability?

Video inspection and incoming material trial runs are supported. On-site visits can also be arranged.

Related products

Get In Touch With Us